Clear-Com Cellcom Instruction Manual Page 74
- Page / 211
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Clear-Com Communication Systems
CellCom V2.0 Instruction Manual
5-4
CHANGING BELTPACK LABELS
The first step in creating a CellCom system is to create individual
names (“labels”) for the wireless beltpacks and for the wired devices
connected to the basestation. Use individual labels for building
“point-to-point” communication routes.
To change a beltpack label
1. From the MAIN menu on the basestation’s front panel display, scroll
to and select BELTPACKS, as shown in Figure 5-4.
.
Figure 5-4: From the MAIN menu, select BELTPACKS
The AVAILABLE BELTPACKS menu appears, as shown in Figure
5-5. The first page shows the first five beltpack labels.
Figure 5-5: Available Beltpacks Menu
• The beltpacks’ generic labels BPK01 through BPK05 appear on
the upper row, while the labels given to the beltpacks appear just
under the generic labels. At first both upper and lower labels will
have the same generic designations.
• To get to the second, third and fourth pages, scroll all the way to
the right of the screen, and then continue to scroll. The second,
third and fourth pages will be displayed showing beltpacks 6 - 10,
11 - 15 and 16 - 20 (BPK06 - BPK10, BPK11 - BPK15, BPK16 -
BPK20).
2. Scroll to and select the desired beltpack label.
The next menu that appears gives the options for programming the
selected beltpack, as shown in Figure 5-6.
Figure 5-6: First Beltpack Programming Options Menu
3. Scroll all the way to the right of the screen and continue to scroll.
The second beltpack programming options menu will be displayed.
MAIN MENU
PORTS
GROUPS SYSTEM
BELTPACKS
AVAILABLE BELTPACKS
BPK02
BPK02
BPK03
BPK03
BPK04
BPK04
BPK05
BPK05
BPK01
BPK01
BACK
SELECTED BPK01 - BPK01
GROUPS
LATCH
BACK
KEYS
Use individual labels for
point-to-point communication
routes.
- DIGITAL WIRELESS 1
- SOFTWARE LICENSE 3
- 2. COPYRIGHT 4
- 3. YOU MAY: 4
- 4. YOU MAY NOT: 4
- 5. TERM: 4
- 6. LIMITED WARRANTY: 4
- 7. LIMITATION OF LIABILITY: 5
- 8. RESTRICTED RIGHTS: 5
- 9. OTHER ISSUES: 5
- CONTENTS 7
- IMPORTANT SAFETY 23
- INSTRUCTIONS 23
- EMC AND SAFETY 24
- GETTING STARTED: 27
- AN INTRODUCTION 27
- TO CELLCOM 27
- CELLCOM FEATURES 28
- System Password 31
- Default Map 31
- QUICK START 33
- TRANSCEIVER 34
- BELTPACKS 36
- CREATING A GROUP 37
- ASSIGNING THE GROUP LABEL TO 37
- CELLCOM BELTPACK KEYS 37
- AUDIO DEVICE 39
- PARTY-LINE BELTPACK 39
- FROM THE BELTPACKS 41
- FROM THE 4-WIRE AUDIO DEVICE 42
- BASESTATION 45
- Level Knob 46
- Display Screen 48
- Setup/Enter Knob 48
- Power Switch 48
- CONNECTING THE 49
- IEC Power Connector 50
- Program Input Connector 50
- PARTY-LINE BELTPACKS 53
- CONNECTIONS 54
- WIRELESS PARTY-LINE 58
- MATRIX INTERCOM 58
- RJ-45 CONNECTOR 59
- AT BASE STATION PORT 59
- COM SYSTEMS 61
- IFB CONFIGURATION 63
- CONNECTING TO A PC 65
- CONNECTING TO 66
- TRANSCEIVER/ANTENNAS (CEL-TA) 66
- SPLITTER (PD2203) 67
- PROGRAMMING A 71
- SYSTEM FROM THE 71
- A NOTE ABOUT TERMINOLOGY 72
- MING MENUS 72
- SAVING CHANGES 72
- BASESTATION PASSWORD 72
- SYSTEM MENU 73
- PASSWORD 73
- CHANGING BELTPACK LABELS 74
- The upper label retains the 76
- Enter name for - HDSTA 77
- V I D E 77
- First create a group label 78
- ADDING GROUP MEMBERS 80
- Figure 5-25: Key Type Menu 83
- SETTING BELTPACK LATCHING 84
- SETTING BELTPACK GROUPS 85
- SETTING BELTPACK LABELS 86
- REGISTERING A BELTPACK 86
- Figure 5-37: Port Levels Menu 88
- SETTING PORT CALL DESTINATION 89
- Figure 5-46: Port Call Menu 90
- CONFIGURING A PARTY LINE 92
- Figure 5-53: VOX Delay Setup 93
- BASESTATION SYSTEM MENU 96
- SYSTEM INFO (“INFO”) 97
- ANTENNAS (“ANTENNAS”) 97
- SETTING THE IP ADDRESS (“IP”) 98
- (“LOCK”) 98
- Figure 5-66: Lock Enable Menu 99
- BATTERY INDICATOR (“BATTERY”) 100
- OPERATING THE 101
- CELLCOM WIRELESS 101
- BELTPACK 101
- BELTPACK TOP CONTROL SECTION 102
- Answer-Back Lights 103
- Combo Button 103
- Left and Right Scroll Buttons 104
- Enter/Answer-Back Button 104
- Backlit LCD Display 104
- BELTPACK BATTERIES 105
- Belt Clip 106
- Data Connector 106
- Headset Connector 106
- BELTPACK TURN-ON SEQUENCE 107
- BELTPACK TURN-OFF SEQUENCE 107
- POWERING THE CELLCOM BELTPACK 107
- THE CELLCOM BELTPACK 110
- HEADSET LIMITER 112
- BELTPACK MENU OPTIONS 113
- AUDIO OPTIONS 114
- VIEW STATUS 115
- Connection Info 116
- Adjust Contrast 116
- PROGRAMMING AT 117
- THE BELTPACK 117
- MAIN PROGRAMMING MENU 118
- THE ALARM OPTIONS MENU 119
- Low Battery Alarm Off 120
- Low Battery Alarm On1 120
- Low Battery Alarm On2 120
- ON AND OFF 121
- THE VIBRA CALL ALERT MENU 121
- THE HEADPHONE MENU 122
- THE MICROPHONE MENU 125
- THE STATUS (INFORMATION) MENU 126
- ADJUST CONTRAST 130
- SET FACTORY DEFAULTS 130
- TAP LATCH 131
- PTT CONFIGURATION 132
- MASTER VOLUME CONTROL 133
- PAGE OPTIONS 134
- CELLCOM 135
- TRANSCEIVER/ 135
- CEL-TA BOTTOM/CONTROL PANEL 136
- CEIVER/ANTENNAS 137
- TRANSCEIVER/ANTENNA SPLITTER 139
- (PD2203) 139
- PD2203 FRONT CONNECTOR PANEL 140
- PD2203 REAR PANEL 141
- INSTALLING A 143
- SYSTEM 143
- DETERMINING COVERAGE AREAS 144
- COVERAGE AREAS 145
- TESTING ANTENNA HANDOFF 147
- Figure 9-3: ANTENNAS menu 148
- CONFIGURATION 151
- COM PORT SELECTION 152
- IP SETUP 152
- BASESTATION VIA ETHERNET 154
- Clear Map 155
- Send File 155
- BELTPACKS TAB 157
- Figure 10-10: Beltpack Label 158
- THE OVERVIEW BUTTON 159
- THE SET DEFAULTS BUTTON 159
- Read Beltpack Settings 160
- Write Beltpack Settings 160
- Remember My Default Settings 160
- Recall My Default Settings 160
- Menu Level 162
- Page Change 162
- Keytap Mode 162
- RSSI Warning 162
- Low Battery Warning 162
- ASSIGNING BELTPACK KEYS 163
- THE REPLY KEY 164
- KEY ASSIGNMENT TYPES 165
- Advanced Menu Setting 166
- Normal Menu Setting 166
- Basic Menu Setting 166
- None Menu Setting 166
- PORTS TAB 167
- TYPE DROP-DOWN BOX 168
- INPUT AND OUTPUT LEVELS 169
- GROUPS TAB 170
- ANTENNAS TAB 171
- CONFIGURING AN IFB 172
- Figure 10-28: Dim Level List 173
- SYSTEM TAB 174
- Figure 10-32: Country Setup 175
- DECT CARRIERS 176
- SYSTEM NUMBER 176
- CELLCOM TOOLKIT 177
- BELTPACK REGISTRATION 183
- BASESTATION SERIAL UPGRADER 184
- BELTPACK SERIAL UPGRADER 187
- RUNNING THE BELTPACK UPGRADER 189
- CABLE PINOUT 190
- SPECIFICATIONS 191
- CellCom CEL-BP Beltpack 192
- Transceiver/Antenna 193
- Transceiver/Antenna Splitter 193
- NOTICE ABOUT SPECIFICATIONS 194
- GLOSSARY 195
- Eclipse Glossary 196
- APPENDIX A: DECT 199
- CARRIER 199
- FREQUENCY CHART 199
- LIMITED WARRANTY 201
- Standard Limited Warranty 202
- APPENDIX B: 205
- PROGRAMMING 205
- NOVEMBER 1, 2008 207
- REPAIR POLICY 210
Related products and manuals for Telephones Clear-Com Cellcom
(62 pages)© 2020, manymanuals.com. All rights reserved. | 1.863 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals