Clear-Com Cellcom User Manual download pdf (Page 6)

CellCom

®

Digital Wireless Intercom Systems

6

CellCom10 Specications

CellCom10 Base Station

Base-to-Beltpack

Frequency

Response

100 Hz – 7.1 kHz.

No. of Beltpacks

per Base Station

10

No. of Transceiver/

Antennas

Supported by

Base, Basic Base

10

No. of Active

Antenna Ports

2

PC Programming

Port

DB9

Relay Port

DB9

Party-Line Intercom

A and Intercom B

(each)

XLR-3F with XLR-3M

loop through, on/off

termination switch

(via software)

Four-Wire/Matrix

Connection

4 RJ-45 (Intercom 3 – 6)

Program Input

XLR-3F, transformer

isolated, line-level input

Stage Announce

Output

XLR-3M, transformer

isolated, line-level

output

Front-Panel

Headset

4-pin male connector

with 2-channel

capability and individual

talks and listens

Front-Panel Display

254 x 32 dot-graphic

VFD

Front-Panel

Indicators

2 Talk LEDs for front-

panel headset, CH A

and CH B party-line

enable LEDs, Program

Input enable LED, 10

individual beltpack

LEDs

Base-Station

Programming/

Editing

Push-to-enter rotary

encoder

Dimensions

1RU unit, 1.75 x 19.0 x

12.5 inches (hwd)

(44 x 483 x 312 mm)

Weight

10.8 lb. (4.9 kg)

Beltpack

Beltpack Frequency

Response

100 Hz – 7.1 kHz

Beltpack

Assignment-Select

Buttons

Access via left and right

scroll buttons, active

“page” indicated on

display “Label”

No. of Pages

3

No. of Full-Duplex

Audio Paths

6 (3 pairs), with

individual level control

Level/Talk Controls

2 top-mounted push-to-

talk rotary encoders

“Page” / Menu

Scroll Buttons

2

Enter / Answer-

Back Button

1

Headset Connector

4-pin male, Clear-Com

standard

Microphone Type

Dynamic, selectable in

beltpack menu

Microphone Level

and Headset

Limiter

Selectable in beltpack

menu

Powering, Alkaline

Battery

4 AA alkaline cells,

Rechargeable: 4 NiMH

cells in AA format

Battery Charging

In unit, via external

power supply

connected to beltpack

Battery Life

8-10 hours with fresh

AA alkaline batteries

or with high-amperage

NiMH cells

Range

Up to 250 m (800

feet) from transceiver/

antenna under ideal

conditions (50 to 150 m

typical)

Dimensions

Tapered design, at

largest points approx.

1.5 x 3.5 x 5.75 inches

(dwh) (38 x 87 x 144

mm)

Weight

(with batteries)

12 oz. (0.35 kg)

Active Antenna

Beltpacks

Supported Per

Active Antenna

5

Active Antenna

Transmission Range

Up to 250 m (800 ft) to

beltpack (50 to 150 m

typical)

Maximum Distance,

Base to Antenna

via Transceiver Port

1,000 m (3,200 ft) on

4-pair CAT-5 or better

cable

Maximum Distance,

Antenna Powered

by Base

300 m (975 ft) on CAT-5

or better cable

Local Powering

24VDC power supply

Connection to

CellCom Base

RJ-45

Antenna Connector

Type

SMA, two; supplied

omnidirectional whip

antennas

Mounting

Via integral tabs with

holes for screws

Dimensions

1.5 x 5.0 x 6.1 inches

(38 x 125 x 153 mm)

Weight

14 oz. (0.4 kg)

Active Splitter

No. of Antennas

5

No. of Splitters Per

Base

2

Connection

Between Base

and Splitter

CAT-5 or better cable

with RJ-45

Connection

Between Splitter

and Antennas

CAT-5 or better cable

with RJ-45

Powering of

Splitter

Locally powered via

supplied external power

supply

Weight

16 oz. (0.45 kg)

Transmission Method

Method of

RF Operation

Uses two slots per

beltpack for wider

frequency response

Modulation

QPSK

Frequencies of

Operation

from 1.92 to 1.93 GHz

(restricted by software)

RF Output

250 mW burst, average

as new FCC level

2 – 4 mW

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments